Favorites
History
My Video
Feedback
The ASIC oil cooling temperature controller has a 1m waterproof temperature probe, which can be placed in the liquid to realize the automatic start and stop function. The dual cooling and heating mode can accurately identify the liquid temperature, set a high-temperature alarm, and delay start and stop. It is an ideal oil cooling control equipment for miners.
Product parameters:
Product name: LCD intelligent temperature controller
Product model: XH-W1631
Temperature range: -19-109°C
Temperature measurement accuracy: +0.1°C
Temperature control accuracy: 1°C
Temperature control range: -19-109°C
Temperature measuring probe: standard 1m waterproof probe
Power supply voltage: DC12-24V
Applicable environment: -15-55℃/20%-85%RH
Output type: direct output
Appearance size: 111x72mm
Embedded size: 92x63mm
Installation hole distance: 101mm
color: blue
Material: ABS
Product weight: 123g
System parameters:
|
serial number |
Describe |
Scope |
Factory default |
|
Start temperature |
Predetermined area |
-19~109℃ |
30℃ |
|
P0 |
Operating mode |
C /H |
H |
|
P1 |
Return difference |
2 |
1-30℃ |
|
P2 |
Correction value |
-10~10℃ |
0℃ |
|
P3 |
Delayed start |
0-10min |
0min |
|
P4 |
High-temperature alarm |
-19~109℃ |
99℃ |
Notice:
1. The screen displays LLL, indicating that the temperature measuring probe is not plugged in, the circuit is broken, or damaged; just replace it;
2. The screen displays HHH, indicating that the temperature measuring probe is short-circuited and exceeds the temperature detection range;
3. To restore the factory settings, press and hold the up and down keys on the right side for over 3 seconds to display 88888 after powering on.
Product connection diagram:
Product function instructions:
1. Mode selection:
① Press and hold the SET button for more than 3 seconds, and the setting display will be P0;
② Short press the SET button again, and H/C flashes;
③Press the up/down key to switch modes (factory default is heating mode H).
2. Start temperature setting:
① Short press the up/down button in normal mode, and the set temperature will flash, and then press the up/down button to adjust the starting temperature.
3. Hysteresis setting:
① Press and hold the SET button for more than 3 seconds, and the setting display will be PO;
②Press the up button to switch to P1 (hysteresis setting);
③Shortly press the SET button again, and the value will flash (the factory value of hysteresis is 2);
④ Press the up/down key to adjust to the desired value.
4. Temperature correction:
① Press and hold the SET button for more than 3 seconds, and the setting display will be P0;
② Press the up and down keys to switch to P2 (temperature correction);
③ Short press the SET key, and the value will flash (factory value is 0);
④Press the up/down key to adjust the value.
5. Delayed start:
① Press and hold the SET button for more than 3 seconds, and the setting display will be PO;
② Press the up and down keys to switch to P3 (delayed start);
③Shortly press the SET button, and the value will flash (the factory value is 0); press the up/down button to adjust the value;
④ After the setting is completed, the thermostat will delay the corresponding time when the starting temperature value is reached and then control the device to start.
6: High-temperature alarm:
① Press and hold the SET button for more than 3 seconds, and the setting display will be P0;
②Press the up/down key to switch to P4 (high-temperature alarm);
③ Short press the SET button, and the value will flash (factory value is 99);
④ Press the up/down key to adjust the value;
⑤ After the setting is completed, the thermostat will emit a beeping beep when the alarm value is reached.
Practical display:
I want to heat the water in a 1500W water heater; how should I set it to control the water temperature at 45-50°C?
1. Press and hold the SET button for more than 3 seconds, the setting display is PO, and the upper display of the confirmed setting is H (heating mode). For example, if C is displayed, you can short press the SET button, C flashes, and press the up/down button to switch to H (heating mode).
2. Wait for 5 seconds, and it will automatically return to normal mode, press the up/down key to adjust the set temperature to 45°C.
3. Press and hold the SET button for more than 3 seconds; the right side displays H and PO; press the up/down button to switch to P1 to set the hysteresis to 45-50°C with a difference of 5°C and adjust the hysteresis value to 5 to complete the setting.
I measured the temperature as 46°C, but the thermostat showed 47°C; how should I adjust it?
1. Press and hold the SET key for more than 3 seconds; the setting display is PO; press the up and down keys to switch to P2 (temperature correction), short press the SET key, and the value flickers (factory value is 0), press the up and down keys to adjust the value, 47 ℃ ratio 46°C is more than 1°C, so subtract 1°C and adjust the value to -1°C.
English
