Watch the tutorial video via the link: https://youtu.be/PFVmyaL7VX8

This method applies to the following situations:

• The miner is power-off in the upgrading process.
• The miner cannot start (cannot find IP).
• The miner can only use the default factory workers.

Tools required:

• The MicroSD card recommended a capacity of less than 16GB. Larger capacity MicroSD cards are not recommended as they are very susceptible to errors.
• A computer running Windows XP or later 
• Card reader

Software required:

• Please contact us to get the image file.

Flashing Instructions :

1. Insert MicroSD card into computer and format to FAT32.
2. Unzip the downloaded image file and copy the contents to the MicroSD card.
3. Edit the file named passwd.txt, and set a password.
4. Remove the MicroSD card from the computer and insert it into the card slot on the control board.
5. Power on the control board. Allow about 30 seconds for the files to load automatically. When loaded, the red and green indicator lights on the control board will blink. (Different models may require different time to complete this process)
6. Power on the miner and access the miner interface. If you could use the password you just set to get into the interface, then you've succeeded recovering the program.

Possible solutions to solve the flashing failure

1. Reformat the MicroSD and make sure you've copied the correct firmware. 

2. Press the MicroSD softly to ensure it's well attached. 

3. Dust and clean the MicroSD.

4. Try with another good known MicroSD.

This method applies to the following situations:

• The miner is power-off in the upgrading process.
• The miner cannot start (cannot find IP).
• The miner can only use the default factory workers.

Tools required:

• The MicroSD card recommended capacity of less than 16GB. Larger capacity MicroSD cards are not recommended as they are very susceptible to errors.
• A computer running Windows XP or later 
• Card reader

Software required:

We use the same image as T9+. Download Link: https://service.bitmain.com/support/download

On the left sidebar click "Flashing SD Card With Image>>Tools and Instructions to Image SD Card. Scroll up to the page and find t9+-SD Tools.zip. Load t9+-SD Tools.zip to your computer in a convenient file location. 

Flashing Instructions :

1. Remove control board from miner assembly.

2. Know your control board model and enable it to flash using the SD card. (See three types of control boards explanation below)

3. Insert MicroSD card into computer and format to FAT32.

4. Unzip the downloaded t9+-SD Tools.zip and copy the contents to the MicroSD card.

5. Insert the MicroSD card into the card slot on the control board

6. Power on the control board. Allow at least 90 seconds for the files to load automatically. When     loaded, the red and green indicator lights on the control board will blink.

7. Power on the control board and access the miner interface. Go to the Upgrade page and Uncheck  “Keep Settings”. Flash the firmware and run the miner for 20 minutes. 

Note that there are three types of control boards and each of them requires a different way to enable flashing.

1. One complete board such as model CRT0401, CRT0402.

Tutorial Video Link: https://youtu.be/6_4oxhVT6hg

To enable it to flash using SD card, you need to shift the JP4 jumper to the right as shown below.

After flashing completed, power off the control board and shift the JP4 jumper back to the original position.

2. Double boards such as model CRT0302.

To enable it to flash using SD card, you need to shortcircuit the AB as shown in the picture below.  

3. Boards without SD card slot such as model CRT0301

It doesn't support SD card flashing.

Possible solutions to solve the flashing failure

1. Reformat the TF and make sure you've copied the correct firmware. 

2. Press the TF softly to ensure it's well attached. 

3. Dust and clean the TF.

4. Try with another good known TF.

The above video for your reference

Tutorial Video Link: https://youtu.be/6_4oxhVT6hg

Notes:

1. T9+ control board is backward-compatible with the S9 and T9. However, the control board of S9 and T9 is not compatible with T9+.

2. The MicroSD card recommended capacity 4GB or 8GB. Larger capacity MicroSD cards are not recommended as they are very susceptible to errors.

3. Computer running Windows XP or later with card reader.

4. Download Link : https://service.bitmain.com/support/download

  On the left sidebar click "Flashing SD Card With Image>>Tools and Instructions to Image SD Card. Scroll up the page and find t9+-SD Tools.zip. Load t9+-SD Tools.zip to your computer in a convenient file location. 

Flashing Instructions :

1. Remove control board from miner assembly.

2. Shift the JP4 jumper to the right as shown below.

3. Insert MicroSD card into computer and format to FAT32.

4. Unzip the downloaded t9+-SD Tools.zip and copy the contents to the MicroSD card.

5. Insert the MicroSD card into the card slot on the control board

6. Power on the control board. Allow at least 90 seconds for the files to load automatically. When loaded, the red and green indicator lights on the control board will blink.

7. Power off the control board and shift the JP4 jumper back to the original position.

8. Power on the control board and access the miner interface. Go to the Upgrade page and Uncheck “Keep Settings”. Flash the firmware and run the miner for 20 minutes.