Video Upload Q&A Likes Trends
@Ada
Check the model of the temperature sensors on the boards and make the necessary changes to the configuration to ensure compatibility.
Several boards have been tested, and all of them show a temperature sensor reading of 0. Even after replacing the three temperature sensor files, the issue persists. What could be the problem causing this issue?
@Ada
Remove the 3rd hashboard and do single-board test to find out the problem.
The total hashrate is consistently insufficient, and there is no temperature reading. The individual board tests show no issues, but the third board continues to lack computational power.
@Ada
Check the kernel logs errors whihc related to the temperature problem. Verify if the temperature sensor model is correct. If the temperature sensor model is incorrect, reconfigure the temperature sensor file to ensure it matches the correct model. If the temperature sensor model is correct,replace the chip to resolve the issue.
The total hashrate is consistently insufficient, and there is no temperature reading. The individual board tests show no issues, but the third board continues to lack computational power.
@Ada
If it passes the single-board test, update the firmware. And then check if the 3 hashboards temp sensor model are consistent. If single-board test fail, there is a temp sensor issue. prioritize replacing the chip on the 62nd board.
If the temperature reading of the 8th board on the backend interface is incorrect, how should it be repaired?
@Ada
First, do not plug in the faulty board with the data cable. Test only the good boards individually to see if they function properly. Tighten the screws and secure the clasps with pliers for a firmer connection. Update the firmware and tighten the screws. Use the voltage adjustment line to supply power, monitor the chip status with the control board, and then adjust the power supply.
S17 hashboard voltage abnormal
@Ada
Do single board test to see the issue. If report 0,check the RI signal from the last chip. If report x asic, check the domain voltage where the chip located.
The last five voltage domains have voltage, while the other domains do not. The 8.5V is present, but the LDOs have no voltage. What could be the problem causing this issue?
@Ada
Test the IO port 3.3V.
What could be the issue if the hashboard does not have an 8.5V voltage supply?
@Ada
Firstly, balance the voltage domains. Alternatively, you can short-circuit the RI signal to provide a stable 1.8V and check if it reports correctly. If the voltage domains are not functioning properly, it is likely that the signals will also be affected and not function correctly.
Which specific signals should be primarily examined when the T15 screen flickers and the RI1.8V signal fluctuates between 0.7V and 1.0V?
@Ada
The 1.8V is directly from BM1387 chip.
In versions without the LOD , no 1.8V domain Voltage, how to check the input of 1.8V?
@Ada
The CO signal voltage of some S9 hashboard versions is only 1.2V. Compare it with another working hashboard of the same model.
Which specific points should be checked when the CO signal on the S9 miner is only 1.2V starting from the first chip?
@Ada
The last 5 domains' 1.8V are in parallel.
T9+ the last 3 domains transmit rule
@Ada
There may be an issue with the 4th voltage domain counted from the end or that there is a missing VDD voltage domain, specifically the 15th voltage domain. The heat sink connected to the 15th voltage domain and 1.8V LDO in 10th voltage domain is conducting. If not conduct,jump to LDO pin 1,pin 3.
The LDO does not have a 2.2V input, but the other voltage domains are functioning normally.
PgUp...2122232425PgDn
Recommend
@steen.wetter
Individual Miner
@telat.uslubas
Other Roles
@Pascal
Enthusiast
@afrialdosiagian
Other Roles
@yuthasad
Mining Farm Owner
@kshtdnrshfaergfr
Other Roles
Hot Topics
Lucky Miner Wi-Fi reconnect
796
Lucky miner v6
784
How To Install Bitmain S19 And S19j Pro Low Power Mode Firmware: Step-By-Step
708
See the below single-board test result. There are 8.4V,8.5V domain voltage, replacing chip 1 did not work.
649
LTC Mining with Lucky Miner Lv06
642
Lucky Miner lv6
640
As shown in the picture below, T15 machine, 58, 59, 60 are all replaced, it still doesn’t work, what’s the problem.
631
L3+ single-board test-- temperature error
608
Lucky miner LV06 breakdown
597
Cannot access IP address lucky miner
569
Hot download
Luckyminer LV06-V2.3.0_upgrade firmware 页面升级固件
981
Luckyminer LV06 factory firmware V2.1.0 页面升级固件
423
Solo Miner_Lucky Miner User Guide LV05-LV08_20231215
321
Luckyminer Management Tool
262
IceRiver_MinerTool_English_V1.0.15 (1)
94
SOLO Miner_Nerdminer USB Shape（V3）配置说明1107
79
Luckyminer LV07 Instruction and User Guide PC English
68
Luckyminer乐透机用户使用说明LV05-LV08(2023.12.15)
64
Luckyminer LV06 ESP-Prog JTAG Debug Guide_Tool kit
57
Luckyminer LV 07 Product Manual
50
No. 88, Yangzishan Road, Chengdu, Sichuan, China
Building A, Zhihui InnovationBuilding, Shenzhen, China
D-2 Seri Gembira Avenue, Kuala Lumpur, Malaysia
+86 15390421113 minerfixesofficial@gmail.com
About Us Contact Us FAQ
Privacy Policy Terms & Conditions
2022 Minerfixes - All Rights Reserved