Video Upload Q&A Likes Trends
If the hashrate drops on Chain 0 and Chain 3 after running for a while. What's the problem?
Chain 0 is not functioning properly, as many chips are returning 0. This is could be due to either a shortage of cores in the chips or i
2023-07-08 08:02
305
0
The test report of S9 hashboard abnormal
As the picture shows, the chip 29 and 57 of all three hashboads has too high data. Reply:Capacitors may not normal, otherwise, the PCB m
2023-07-08 07:49
316
0
S9 hashboard RI is normal from chip 63 to chip 1,short CO at chip 1,but report 0
One of the chips may be short-circuiting and pulling down the RST voltage. Check if any chip is causing a short circuit and affecting th
2023-07-08 07:42
292
0
The S9 control board top surface only 1 light on.
The initial assessment indicates that the control board is burnt. Connect to the serial port and check for any logs. If that doesn't wor
2023-07-08 07:34
293
0
How to determine which voltage domain is normal when the L3+ hashboard has voltage domain imbalance?
Test the specific domain that is experiencing an imbalance.If the chip is not the issue, it is likely that the small capacitors are faul
2023-07-08 07:30
308
0
Z11 hashboard is short-circuited to ground at 3.3V. After removing the IC (U3), inductor (L1) and capacitors (20, 22, 23, 24), the short circuit issue persists.
Check the LDO circuit. Remove C21,C13,U3 to verify. If the issue still exist, the power IC broken, test the power manage IC one by one.
2023-07-08 07:14
332
0
S9 hashboard report 0, No RI signal, replace chip 62 and chip 63, power on but still no signals.
Replace chip 61, make sure the chip is OK.
2023-07-08 07:02
326
0
Z11 hashboard LDO without 3.3V, Pin 1 with 12V input voltage.
Add DC 3.3V power to the "L1" to check the current. If current is normal, repair the above circuit. If current is abnormal, repair th
2023-07-08 06:59
345
0
S9 hashboard the voltage and resistance are both normal, replace severial chips but stil report 50.
Short the CO signal of chip 50. If report 50, replace number 51 chip. If report 49, replace number 50 chip.
2023-07-08 06:40
324
0
The S9 hashboard report asic 62, replace the 62nd chip but still the same problem still exists.
Short the output CO signal of the 62nd chip.If report 62, replace the number 63 chip. If report 61 or other digital, continue to short t
2023-07-08 06:36
331
0
PgUp12345PgDn
Recommend
@cooliepplz718
Enthusiast
@norbert.szimeth
Other Roles
@alvarosutana
Other Roles
@9.8
Other Roles
@pchelpline
Enthusiast
@geyshakulor
Individual Miner
Hot Topics
Lucky Miner Wi-Fi reconnect
800
Lucky miner v6
794
How To Install Bitmain S19 And S19j Pro Low Power Mode Firmware: Step-By-Step
709
See the below single-board test result. There are 8.4V,8.5V domain voltage, replacing chip 1 did not work.
652
LTC Mining with Lucky Miner Lv06
644
Lucky Miner lv6
642
As shown in the picture below, T15 machine, 58, 59, 60 are all replaced, it still doesn’t work, what’s the problem.
633
L3+ single-board test-- temperature error
611
Lucky miner LV06 breakdown
601
Cannot access IP address lucky miner
575
Hot download
Luckyminer LV06-V2.3.0_upgrade firmware 页面升级固件
988
Luckyminer LV06 factory firmware V2.1.0 页面升级固件
427
Solo Miner_Lucky Miner User Guide LV05-LV08_20231215
321
Luckyminer Management Tool
264
IceRiver_MinerTool_English_V1.0.15 (1)
95
SOLO Miner_Nerdminer USB Shape（V3）配置说明1107
79
Luckyminer LV07 Instruction and User Guide PC English
69
Luckyminer乐透机用户使用说明LV05-LV08(2023.12.15)
64
Luckyminer LV06 ESP-Prog JTAG Debug Guide_Tool kit
58
Luckyminer LV 07 Product Manual
50
No. 88, Yangzishan Road, Chengdu, Sichuan, China
Building A, Zhihui InnovationBuilding, Shenzhen, China
D-2 Seri Gembira Avenue, Kuala Lumpur, Malaysia
+86 15390421113 minerfixesofficial@gmail.com
About Us Contact Us FAQ
Privacy Policy Terms & Conditions
2022 Minerfixes - All Rights Reserved